Barcode Scanners - Revision history

Russ horton: /* USB HID POS */

2021-02-17T20:16:14Z

USB HID POS

← Older revision		Revision as of 20:16, 17 February 2021
Line 30:		Line 30:
	Support for this mode of scanning was added in CMS TEN and should be your first choice where possible. It is also the only mode supported in Windows 10 currently. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to setup and use with no driver software to install. They are about as close as you'll get to plug and play.		Support for this mode of scanning was added in CMS TEN and should be your first choice where possible. It is also the only mode supported in Windows 10 currently. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to setup and use with no driver software to install. They are about as close as you'll get to plug and play.

	Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.		Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners.

	==='''SUPPORTED SCANNER MODELS:'''===		==='''SUPPORTED SCANNER MODELS:'''===

Russ horton: /* SUPPORTED SCANNER MODELS: */

2020-02-20T20:37:33Z

SUPPORTED SCANNER MODELS:

← Older revision		Revision as of 20:37, 20 February 2020
Line 33:		Line 33:

	==='''SUPPORTED SCANNER MODELS:'''===		==='''SUPPORTED SCANNER MODELS:'''===
	'''[[WINDOWS 10 USERS]]''' - Honeywell has been unable to get USB Serial Emulation to work on Win10. If you expect to need a barcode scanner on a Win10 machine, please choose a scanner model that supports USB HID POS mode (below).		'''[[WINDOWS 10 USERS]]''' - Honeywell has been unable to get USB Serial Emulation to work on Win10. If you expect to need a barcode scanner on a Win10 machine, please choose a scanner model that supports USB HID POS mode (below):

	**Honeywell 1300G (replaced the 3800G) - ''Supports only USB HID POS''		**Honeywell 1300G (replaced the 3800G) - ''Supports only USB HID POS''

Russ horton: /* Scanners */

2016-08-18T21:32:40Z

Scanners

← Older revision		Revision as of 21:32, 18 August 2016
Line 26:		Line 26:
	*Products (CMS Ten+)		*Products (CMS Ten+)
	*Stock Manager (CMS Ten+)		*Stock Manager (CMS Ten+)

			===USB HID POS===
			Support for this mode of scanning was added in CMS TEN and should be your first choice where possible. It is also the only mode supported in Windows 10 currently. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to setup and use with no driver software to install. They are about as close as you'll get to plug and play.

			Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.

	==='''SUPPORTED SCANNER MODELS:'''===		==='''SUPPORTED SCANNER MODELS:'''===
Line 56:		Line 61:
	**MS3580 QuantumT		**MS3580 QuantumT
	While these scanners do have to be programmed to work in the USB HID POS mode (aka USB HID serial mode, '''not''' USB HID SurePOS or USB HID keyboard) there should be no driver installation necessary as there is with USB serial emulation. You'll just need to find the proper bar code to scan in the scanner's programming guide for USB HID. You can purchase a scanner and ship it to us if you'd like us to add it to our supported scanner list. We can then provide documentation on proper setup and help with troubleshooting any future issues.		While these scanners do have to be programmed to work in the USB HID POS mode (aka USB HID serial mode, '''not''' USB HID SurePOS or USB HID keyboard) there should be no driver installation necessary as there is with USB serial emulation. You'll just need to find the proper bar code to scan in the scanner's programming guide for USB HID. You can purchase a scanner and ship it to us if you'd like us to add it to our supported scanner list. We can then provide documentation on proper setup and help with troubleshooting any future issues.

	~~===USB HID POS===~~
	Support for this mode of scanning was added in CMS TEN and should be your first choice where possible. It is also the only mode supported in Windows 10 currently. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to setup and use with no driver software to install. They are about as close as you'll get to plug and play.

	Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.

	===Serial Scanner Programming===		===Serial Scanner Programming===
Line 66:		Line 66:
	While NewHaven Software offers support and programming instructions for a select number of scanner models (available from [http://updates.newhavensoftware.com/ Support Downloads]), chances are most any scanner can be programmed to work with CMS. If you'd like NewHaven Software to certify your preferred scanner model, just have one shipped to us. In return we will provide step by step setup instructions and ongoing support for your use of that scanner model. If we get it to work, we keep the unit for future testing and support. If we cannot get it to work, we'll ship it back. Contact your account rep or technical support for more details.		While NewHaven Software offers support and programming instructions for a select number of scanner models (available from [http://updates.newhavensoftware.com/ Support Downloads]), chances are most any scanner can be programmed to work with CMS. If you'd like NewHaven Software to certify your preferred scanner model, just have one shipped to us. In return we will provide step by step setup instructions and ongoing support for your use of that scanner model. If we get it to work, we keep the unit for future testing and support. If we cannot get it to work, we'll ship it back. Contact your account rep or technical support for more details.

	If instead you'd like to take a crack at it on your own, here are the elements we look for when programming a scanner:		If instead, you'd like to take a crack at it on your own, here are the elements we look for when programming a scanner:

	#Get the manual - If you don't have it handy, download a copy from the manufacture's website. Most are available in a .pdf format.		#Get the manual - If you don't have it handy, download a copy from the manufacture's website. Most are available in a .pdf format.

Russ horton: /* Models Supported */

2016-08-18T21:30:54Z

Models Supported

@@ Line 27: / Line 27: @@
 *Stock Manager (CMS Ten+)
-===Models Supported===
+==='''SUPPORTED SCANNER MODELS:'''===
-Please see our [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of supported brands/models.
+'''[[WINDOWS 10 USERS]]''' - Honeywell has been unable to get USB Serial Emulation to work on Win10. If you expect to need a barcode scanner on a Win10 machine, please choose a scanner model that supports USB HID POS mode (below).
 ===USB HID POS===

Russ horton: /* USB HID POS */

2016-08-16T23:31:10Z

USB HID POS

← Older revision		Revision as of 23:31, 16 August 2016
Line 31:		Line 31:

	===USB HID POS===		===USB HID POS===
	Support for this mode of scanning was added in CMS ~~Ten~~ and should be your first choice where possible. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to ~~program,~~ setup, and use with no driver software to install. ~~About~~ as close as you'll get to plug and play.		Support for this mode of scanning was added in CMS TEN and should be your first choice where possible. It is also the only mode supported in Windows 10 currently. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to setup and use with no driver software to install. They are about as close as you'll get to plug and play.

	Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.		Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.

Russ horton: /* Serial Scanner Programming */

2016-04-19T18:32:06Z

Serial Scanner Programming

← Older revision		Revision as of 18:32, 19 April 2016
Line 44:		Line 44:
	#Get the Windows driver - Here again, download from the manufacture's website if you do not have a driver disk or know the location of the driver file		#Get the Windows driver - Here again, download from the manufacture's website if you do not have a driver disk or know the location of the driver file
	#Reset Product Defaults - scan the code that resets the scanner back to factory defaults		#Reset Product Defaults - scan the code that resets the scanner back to factory defaults
	#USB Com Port Emulation - If the scanner is connected by USB (recommended), scan the code to enable USB Com Port Emulation. When programming a scanner to operate in serial mode, Windows will immediately recognize it, assign a COM port, and prompt you to install new hardware. Be prepared for this and have the driver handy, ideally in a ~~subdirectory~~ of NewHaven Software on the network for easy access to all workstations (each workstation using a serial scanner will need its own driver). Drivers for supported scanners are included on CMS CD's that we ship and are available on request along with the scanner's PDF manuals used for programming the scanners.		#USB Com Port Emulation - If the scanner is connected by USB (recommended), scan the code to enable USB Com Port Emulation. When programming a scanner to operate in serial mode, Windows will immediately recognize it, assign a COM port, and prompt you to install new hardware. Be prepared for this and have the driver handy, ideally in a sub-directory of NewHaven Software on the network for easy access to all workstations (each workstation using a serial scanner will need its own driver). Drivers for supported scanners are included on CMS CD's that we ship and are available on request along with the scanner's PDF manuals used for programming the scanners.
	#Add a ~~Carraige~~ Return (CR) suffix - scan the code in the programming guide that appends a ~~carraige~~ return after every scan		#Add a Carriage Return (CR) suffix - scan the code in the programming guide that appends a carriage return after every scan
	#Remove the Line Feed (LF) suffix - Not all scanners default to include this but if yours does, you'll want to disable it		#Remove the Line Feed (LF) suffix - Not all scanners default to include this but if yours does, you'll want to disable it
	#Configure CMS to work with your scanner - In CMS the setup for serial scanners is in Workstation Specific under the Serial Dev tab. There you can click test to confirm it is working properly (you will see the contents of your scan in the box next to Test.) Refer to Device Manager in Windows if you are unsure of the com port assigned to the scanner. Default baud is typically 9600.		#Configure CMS to work with your scanner - In CMS the setup for serial scanners is in Workstation Specific under the Serial Dev tab. There you can click test to confirm it is working properly (you will see the contents of your scan in the box next to Test.) Refer to Device Manager in Windows if you are unsure of the com port assigned to the scanner. Default baud is typically 9600.

Russ horton: /* Serial Scanner Programming */

2016-04-19T18:31:21Z

Serial Scanner Programming

← Older revision		Revision as of 18:31, 19 April 2016
Line 46:		Line 46:
	#USB Com Port Emulation - If the scanner is connected by USB (recommended), scan the code to enable USB Com Port Emulation. When programming a scanner to operate in serial mode, Windows will immediately recognize it, assign a COM port, and prompt you to install new hardware. Be prepared for this and have the driver handy, ideally in a subdirectory of NewHaven Software on the network for easy access to all workstations (each workstation using a serial scanner will need its own driver). Drivers for supported scanners are included on CMS CD's that we ship and are available on request along with the scanner's PDF manuals used for programming the scanners.		#USB Com Port Emulation - If the scanner is connected by USB (recommended), scan the code to enable USB Com Port Emulation. When programming a scanner to operate in serial mode, Windows will immediately recognize it, assign a COM port, and prompt you to install new hardware. Be prepared for this and have the driver handy, ideally in a subdirectory of NewHaven Software on the network for easy access to all workstations (each workstation using a serial scanner will need its own driver). Drivers for supported scanners are included on CMS CD's that we ship and are available on request along with the scanner's PDF manuals used for programming the scanners.
	#Add a Carraige Return (CR) suffix - scan the code in the programming guide that appends a carraige return after every scan		#Add a Carraige Return (CR) suffix - scan the code in the programming guide that appends a carraige return after every scan
	#Remove the Line Feed (LF) suffix - Not all scanners default to include this but if yours does, you want to disable it		#Remove the Line Feed (LF) suffix - Not all scanners default to include this but if yours does, you'll want to disable it
	#Configure CMS to work with your scanner - In CMS the setup for serial scanners is in Workstation Specific under the Serial Dev tab. There you can click test to confirm it is working properly (you will see the contents of your scan in the box next to Test.) Refer to Device Manager in Windows if you are unsure of the com port assigned to the scanner. Default baud is typically 9600.		#Configure CMS to work with your scanner - In CMS the setup for serial scanners is in Workstation Specific under the Serial Dev tab. There you can click test to confirm it is working properly (you will see the contents of your scan in the box next to Test.) Refer to Device Manager in Windows if you are unsure of the com port assigned to the scanner. Default baud is typically 9600.

Russ horton: /* Scanners */

2015-03-31T17:28:22Z

Scanners

← Older revision		Revision as of 17:28, 31 March 2015
Line 24:		Line 24:
	*POS Module (all CMS versions)		*POS Module (all CMS versions)
	*Manifest (all CMS versions)		*Manifest (all CMS versions)
	*Products (~~10.0~~+)		*Products (CMS Ten+)
	*Stock Manager (~~10.0~~+)		*Stock Manager (CMS Ten+)

	===Models Supported===		===Models Supported===
Line 31:		Line 31:

	===USB HID POS===		===USB HID POS===
	Support for this mode of scanning was added in CMS ~~10.0~~ and should be your first choice where possible. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to program, setup, and use with no driver software to install. About as close as you'll get to plug and play.		Support for this mode of scanning was added in CMS Ten and should be your first choice where possible. Despite the name, scanners running in the HID POS mode are not limited to use in point of sale (POS.) They can be used wherever CMS supports scanner input. HID POS scanners are faster to program, setup, and use with no driver software to install. About as close as you'll get to plug and play.

	Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.		Not all scanners support this mode but many of the popular ones do and should only require a single programming code scan to put your scanner in this mode. Look for USB HID or HID POS in your scanners programming guide if you're using an unsupported scanner otherwise contact NewHaven Software for a programming instruction sheet for one of our supported scanners. See our wiki page on [http://wiki.newhavensoftware.com/index.php/CMS_System_Requirements#Peripherals CMS System Requirements] for a current list of known and supported scanners that can operate in this mode.

Russ horton: /* Scanners */

2014-08-25T16:27:24Z

Scanners

← Older revision		Revision as of 16:27, 25 August 2014
Line 16:		Line 16:

	==Scanners==		==Scanners==
	As described above, scanners can work in a serial (or serial emulation for USB) ~~mode~~ or keyboard emulation. Most any scanner can be programmed to work with either method. Changing between them is typically just a matter of scanning barcodes in the scanner's manual to program the options you want to use. Some scanners, however, will require specific cables for different communication types and, to facilitate these, most scanners' cables can be replaced.		As described above, scanners can work in a serial mode (serial emulation for USB) or keyboard emulation. Most any scanner can be programmed to work with either method. Changing between them is typically just a matter of scanning barcodes in the scanner's manual to program the options you want to use. Some scanners, however, will require specific cables for different communication types and, to facilitate these, most scanners' cables can be replaced.

	Not sure what mode your scanner is in? Open Notepad and scan any barcode (coke can, ~~candybar~~, tracking number, etc.) and if the text shows up in Notepad, the scanner is in keyboard emulation mode. If you see nothing, chances are it is in serial emulation mode.		Not sure what mode your scanner is in? Open Notepad and scan any barcode (coke can, candy bar, tracking number, etc.) and if the text shows up in Notepad, the scanner is in keyboard emulation mode. If you see nothing, chances are it is in serial emulation mode.

	Presently CMS will work with serial scanners (again this includes USB scanners operating in serial emulation mode) in the following places:		Presently CMS will work with serial scanners (again this includes USB scanners operating in serial emulation mode) in the following places:

Russ horton: /* Scanners */

2014-08-25T16:25:21Z

Scanners

← Older revision		Revision as of 16:25, 25 August 2014
Line 22:		Line 22:
	Presently CMS will work with serial scanners (again this includes USB scanners operating in serial emulation mode) in the following places:		Presently CMS will work with serial scanners (again this includes USB scanners operating in serial emulation mode) in the following places:

	*POS Module (all)		*POS Module (all CMS versions)
	*Manifest (all)		*Manifest (all CMS versions)
	*Products (10.0+)		*Products (10.0+)
	*Stock Manager (10.0+)		*Stock Manager (10.0+)